Flash Point Tester

Test Method: - Flash Point is lowest temperature at which application of the ignition source causes the vapor of a specimen of the sample to ignite under the specified condition of the test. The temperature of the approximately 70 ml test specimen is increased rapidly at first and then at a slower constant rate as the flash point is approached. At specified intervals a test flame is passed across the cup, to measure the tendency of the test specimen to form a flammable mixture with air under controlled laboratory conditions.
Standard: - Conforms to the specifications of ASTM D92; IP 36; ISO 2592
Features & Benefits: -
1)     Temp Range: 79 to 400° Deg. C.
2)     Test Method: ISO 2592, ASTM D 92, IP 36, IS 1448 (P-69)
.3)     Ignition Source: Gas Flame with two Pilot electric Coils.
4)     Temperature Sensor: PT-100 in stainless steel sheath.
5)     Flash/Fire Detector: Manual / Visual flash detection.\
6)     Controller: Current regulators which limit the current flowing to the heater, thus give us very accurate control and long life to heater.
7)     Flame-Sampling Arrangement: 10 Rpm, D.C. 12 v or 24V DC, gear motor, vertical movement reciprocating to & fro motion.
8)     Heater: 800 W, 230v.
9)     Electrical ignition for pilot flame-sampling. Ignition transformer having continuous o/p of 10.6 Kv. D.C. from 230 v A.C. i/p.
10)  Equipment Overall Size (LxWxH): 280mm (W) X 530mm ( D ) X 415 mm ( H )
11)  Equipment Gross Weight: 22 Kg.
12)  Equipment supply will be 230 V Ac , 50 Hz with 15 amp capacity.

Accessories Will Be Supplied With Equipment: -

 1)     COC CUP   --  1 NO (CAT NO HAMCO19AC1)
2)     THERMAL FUSE – 1 NO. (CAT NO HAMCO19AC5)
3)     SIGNAL CABLE - 1 NO. ( CAT NO HAMCO 19AC6)

Dimension: - Ixwxh,in.(cm)

11”x22”x17” (28x53x41)
Net Weight: 49 lbs (22kg) 

Shipping Information: - 

 Shipping Weight: 78 lbs (35kg)
Dimensions: 4.7 Cu. ft. 

Ordering Information: -

Additional Information:

Item Code: HAMCO19C

TEST METHOD :- Flash Point is Lowest temperature at which application of the ignition source causes the vapour of a specimen of the sample to ignite under the specified condition of the test.The temperature of the approximately 70 ml test specimen is increased rapidly at first and then at a slower constant rate as the flash point is approached. At specified intervals a test flame is passed across the cup, to measure the tendency of the test specimen to form a flammable mixture with air under controlled laboratory conditions.
STANDARD :- Conforms to the specifications of:
ASTM D92; IP 36; ISO 2592
FEATURES & BENEFITS :-
1)      Temp.Range: 79  to 400° deg C.
2)      Test Method : ISO 2592 , ASTM D 92 , IP 36 , IS 1448 ( P-69).
3)      Ignition Source : Crank Mechanisam spring loaded with manual handling.
4)      Temperature Sensor : Digital temperature Indicator RTD Type 
5)      Flash/Fire Detector: Manual / Visual flash detection.
6)      Controller: Current regulator which limit the current flowing to the heater, thus give us very accurate control and long life to heater..
7)      Flame-Sampling Arrangement: By Hand.
8)      Heater: 800 W, 230 v.
9)      Equipment Overall Size (LxWxH): 175mm (W) X 300mm ( D ) X 300 mm ( H )
10)  Equipment Gross Weight:12 Kg.
11)  Equipment supply will be 230 V Ac , 50 Hz with 6 amp capacity.

ACCESSORIES WILL BE SUPPLID WITH EQUIPMENT :-
1)      COC CUP   --  1 NO (CAT NO HAMCO19AC1)
2)      THERMOMETER COLLAR – 1 NO ( CAT NO HAMCO19AC2)
3)      DIGITAL TEMPERATURE INDICATOR – 1 NO (CAT NO HAMCO19AC4)

SPARES REQUIRED FOR 5 YEAR TROUBLE FREE OPERATION :-
1)      CERAMIC HEATER  --  2 NOS.(CAT NO HAMCO19S1)
2)      COC CUP  --  2 NO.(CAT NO HAMCO19AC1) 

ELECTRICAL REQUIREMENT –
·         220-240V, 50/60Hz, Single Phase, 5.9A
·         OR 115V, 50/60Hz, Single Phase, 11.8A 

DIMENSION :- Ixwxh,in.(cm)
7”x12”x12” (18x30x30)
Net Weight: 27 lbs (12kg) 

SHIPPING INFORMATION :- 

Shipping Weight: 46 lbs (21kg)
Dimensions: 2.75 Cu. ft.       

ORDERING INFORMATION :- 

Additional Information:

Item Code: HAMCO19B

TEST METHOD :- Flash Point is Lowest temperature at which application of the ignition source causes the vapour of a specimen of the sample to ignite under the specified condition of the test.The temperature of the approximately 70 ml test specimen is increased rapidly at first and then at a slower constant rate as the flash point is approached. At specified intervals a test flame is passed across the cup, to measure the tendency of the test specimen to form a flammable mixture with air under controlled laboratory conditions.
STANDARD :- Conforms to the specifications of:ASTM D92; IP 36; ISO 2592
FEATURES & BENEFITS :-
1)      Temp.Range: 79  to 400° deg C.
2)      Test Method : ISO 2592 , ASTM D 92 , IP 36 , IS 1448 ( P-69).
3)      Ignition Source : Crank Mechanisam spring loaded with manual handling.
4)      Temperature Sensor : Thermometer .
5)      Flash/Fire Detector: Manual / Visual flash detection.
6)      Controller: Energy regulator manual type.
7)      Flame-Sampling Arrangement: By Hand.
8)      Heater: 800 W, 230 v.
9)      Equipment Overall Size (LxWxH): 175mm (W) X 200mm ( D ) X 275 mm ( H )
10)  Equipment Gross Weight: 8 Kg.
11)  Equipment supply will be 230 V Ac , 50 Hz with 6 amp capacity.
ACCESSORIES WILL BE SUPPLID WITH EQUIPMENT :-
1)      COC CUP   --  1 NO (CAT NO HAMCO19AC1)
2)      THERMOMETER COLLAR – 1 NO ( CAT NO HAMCO19AC2)
3)      THERMOMETER ASTM 11C – 1 NO (CAT NO HAMCO19AC3)

SPARES REQUIRED FOR 5 YEAR TROUBLE FREE OPERATION :-
1)      CERAMIC HEATER  --  2 NOS.(CAT NO HAMCO19S1)
2)      COC CUP  --  2 NO.(CAT NO HAMCO19AC1)
3)      THERMOMETER ASTM 11C – 1 NO (CAT NO HAMCO19AC3)
ELECTRICAL REQUIREMENT –
·         220-240V, 50/60Hz, Single Phase, 5.9A
·         OR 115V, 50/60Hz, Single Phase, 11.8A 

DIMENSION :- Ixwxh,in.(cm)
7”x8”x11” (18x20x28)
Net Weight: 18 lbs (8kg) 

SHIPPING INFORMATION :- 

Shipping Weight: 33 lbs (15kg)
Dimensions: 1.75 Cu. ft.      

ORDERING INFORMATION :- 

Additional Information:

Item Code: HAMCO19A

Product Details:

Test Method: - Flash Point is lowest temperature at which application of the ignition source causes the Vapour of a specimen of the sample to ignite under the specified condition of the test.The temperature of the approximately 70 ml test specimen is increased rapidly at first and then at a slower constant rate as the flash point is approached.
Standard: - Conforms to the specifications of:ASTM D93; IP 34; ISO 2719
Features & Benefits:-
1)     Temp. Range: 40 to 400° deg C.
2)     Test Method: ISO 2719, ASTM D 93, IP 34, IS 1448 (P-21).
3)     Ignition Source: Electrical ignitor with LPG gas connection.
4)     Temperature Sensor: PT-100 in stainless steel sheath.
5)     Flash Detector: CRC Thermocouple.
6)     Controller: Touch Screen, Colour Display with PLC with audio visual alarm to check the machine. 3-wire RTD temperature sensor, free potential flame detector sensor as i/p. with automatic barometric reading correction.
7)     Inbuilt storage memory for Flash Detection.
8)     Flame-Sampling Arrangement: 10 Rpm, D.C. 12 v or 24V DC, gear motor, vertical movement reciprocating to & fro motion.
9)     Heater: 800 W, 230v.
10)  Electrical ignition flame-sampling. Ignition transformer having continuous o/p of 10.6 Kv. D.C. from 230 v A.C. i/p.
11)  Equipment Overall Size (LxWxH): 280mm (W) X 530mm ( D ) X 415 mm ( H )
12)  Equipment Gross Weight: 22 Kg.
13)  Equipment supply will be 230 V Ac, 50 Hz with 15 amp capacity.
Features:-Single Action Setting: - The Flash Detection sensor and temperature sensor are permanently mounted on a lid, which allows easy setting of the specimen.Easy Operation: - Select a Test Mode and enter the expected flash Point. While instrument executes the test, you are free to do other lab work. The tester follows the exact procedures prescribed in the test method and the completion of the test cycle is signalled by buzzer. The test result is brightly shown in VFD and same will be stored in the HMI.
Automatically Shut The Machine And Horn The Buzzer In The Case:

Accessories Will Be Supplied With Equipment:-
1)     Pensky Martene  Cup & Lid  --  1 No (Cat No Hamco30ac1)
2)      Thermal Printer  -- 1 No (Cat No Hamco30ac7)
3)     Thermal Printer Roll  --  1 No (Cat No Hamco30ac8)
4)     Pc Interface Cable – 1 No. (Cat No Hamco30ac9)
5)     Software For Above-- 1 No. (Cat No Hamco30ac10)
6)     Thermal Fuse – 1 No. (Cat No Hamco30ac5)
7)     Signal Cable - 1 No. ( Cat No Hamco 30ac6)
Ordering Information:-

Additional Information:

Item Code: HAMCO30D

Pay Mode Terms: T/T (Bank Transfer)

Port of Dispatch: JNPT

Production Capacity: 10

Delivery Time: 4 TO 6 WEEK

Packaging Details: WOODEN BOX

Product Details:

Additional Information:

Item Code: HAMCO30C

Pay Mode Terms: T/T (Bank Transfer)

Port of Dispatch: JNPT

Production Capacity: 100

Delivery Time: 3 WEEKS

Packaging Details: WOODEN BOX

Product Details:

This flash point and fire-point test method is a dynamic method and depends on definite rates of temperature increases to control the precision of the method. Its primary use is for viscous materials having a flash point between 79°C (175°F) and 400°C (752°F) except fuel oils, to define the hazards of flammable and combustible materials used in shipping and safety regulations.

The temperature of the approximately 70 ml test specimen is increased rapidly at first and then at a slower constant rate as the flash point is approached. At specified intervals a test flame is passed across the cup, to measure the tendency of the test specimen to form a flammable mixture with air under controlled laboratory conditions

• The flash point is the lowest liquid temperature at which application of the flame causes the vapors of the test specimen of the sample to ignite.

• To determine the fire-point, the test is continued until the application of the test flame causes the test specimen to ignite and sustain burning for a minimum of 5s.

It is an automatic flash and fire-point tester used to examine liquid as well as highly viscous samples in the same instrument without any additional equipment. For substances with unknown flash points, the APPARATUS has a special search mode program. During the entire heating period, the test flame is moved across the sample at suitable intervals. The expected flash point of a specimen can thereby be found in a time saving and economical manner.

• Optional On demand: When examining highly viscous specimens, a preheating time and temperature are set in order to warm-up and liquefy the sample to inserted temperature probe without problem. Further a skimmer is removing the surface skin from bituminous samples.

• Standard Cup with handle, made of brass

• Temperature Probe Pt-100 for sample temperature

• Electric Gas Igniter with connector cable and plugs

Flame Detection Unit for the detection of flash- and fire-points Flame Arrest Cover for extinguishing the fire in the cup PC Interface Programmed Controller. The Unit is incorporated with MODBUS RTU PC interface Microprocessor based PID Programmable
controller user friendly features.

Details:

Fully Automatic Flash and Fire point apparatus.

• Controller: Microprocessor based process controller cum indicator with touch screen with LED Display with audio visual alarm to check the machine. 3-wire RTD temperature sensor, free potential flame detector sensor as i/p. The controller having capacity of storing 200 data with automatic barometric reading correction.

• It is with PC Interface for data storing.

• Printer with data interface cable for taking the reading of Flash Point after completion of the cycle.

• Flame-Sampling Arrangement: 10 Rpm, D.C. 12 v or 24V DC, gear motor, vertical movement reciprocating to & fro motion.Heater: 800 W, 230 v.

• Electrical ignition for pilot flame-sampling. Ignition transformer having continuous o/p of 10.6 Kv. D.C. from 230 v A.C. i/p.